Search found 917 matches
- Fri Mar 25, 2022 8:01 pm
- Forum: Technical
- Topic: Penny Tech - Plug wrench Mod
- Replies: 2
- Views: 5196
Penny Tech - Plug wrench Mod
Hi, This for all you hard core Dualsport guys that like to ride 2T when you really want to have fun. A good tool kit is minimal but can still do a top end in the bush. Its all about making the most of the tools in your kit and making room for more. I was not able to source a 27mm nut without spendin...
- Wed Jun 10, 2020 6:51 am
- Forum: Technical
- Topic: JD jetting chart for mikuni
- Replies: 1
- Views: 4731
Re: JD jetting chart for mikuni
I got a copy of the jetting guide, thanks
- Thu Jun 04, 2020 7:24 am
- Forum: Technical
- Topic: JD jetting chart for mikuni
- Replies: 1
- Views: 4731
JD jetting chart for mikuni
Hi, any one have a copy of the jd jetting chart for a ktm 250 with the mikuni carb. Bought a bike with the kit installed but no jetting chart
Thanks
Thanks
- Thu Sep 19, 2019 3:29 pm
- Forum: Want Ads
- Topic: WTB 2017 Husqvarna Fork and Shock Springs: TE300 and FE501
- Replies: 5
- Views: 8071
Re: WTB 2017 Husqvarna Fork and Shock Springs: TE300 and FE501
What rates and lengths are you looking for?
- Fri Jun 14, 2019 3:18 pm
- Forum: Bikes For Sale
- Topic: 2016 KTM 350XCF For Sale
- Replies: 0
- Views: 6785
2016 KTM 350XCF For Sale
2016 KTM 350XCF For Sale - P3 skid plate and Obie Link guard - scorpion Rad guards - new side and front number plastics (not in the pics, keeping my old plastics) - forks have race-tech compression bases, valving for a 200lbs rider, can be converted back to stock config if you prefer. - TM Designs c...
- Fri Jun 14, 2019 2:40 pm
- Forum: Bikes For Sale
- Topic: 2007 Kawasaki KLX125
- Replies: 0
- Views: 6441
2007 Kawasaki KLX125
Asking $1400
You can PM me or Text\Call 403-819-0026- Tue Jun 04, 2019 3:03 pm
- Forum: Technical
- Topic: Countershaft
- Replies: 6
- Views: 6663
Re: Countershaft
Maybe my bad , last counter shaft bearing i replaced was a garden variety ball bearing. Read the op again and sounds like some fancy speciality caged bearing design. I am out
- Tue Jun 04, 2019 6:49 am
- Forum: Technical
- Topic: Countershaft
- Replies: 6
- Views: 6663
Re: Countershaft
Sounds like you are talking about what is called a dust seal that sits between the inner and outer race of the bearing. It can be removed if it’s a concern.
- Fri May 24, 2019 10:27 am
- Forum: Technical
- Topic: Cheap Grip Heaters
- Replies: 10
- Views: 8459
Re: Cheap Grip Heaters
If the ground is not floating on the circuit you use from the stator, the full wave rectifier will only convert half the ac current to dc. Yeah this feels like dejavu. Lower right corner of the attached diagram is the hookup you should have, since you have not floated the ground. Based on a quick re...
- Fri May 24, 2019 7:43 am
- Forum: Technical
- Topic: Cheap Grip Heaters
- Replies: 10
- Views: 8459
Re: Cheap Grip Heaters
I just notice you update. Your rectifier is only converting half the power from the ac yellow wire to dc( half the ac wave). Read up on floating the ground and full wave rectifiers. Tons of power for the led, and leds will not really dim much as you drop voltage and have a wide operating volt range,...
- Fri May 24, 2019 7:25 am
- Forum: Technical
- Topic: Cheap Grip Heaters
- Replies: 10
- Views: 8459
Re: Cheap Grip Heaters
If you tap into the stock headlight that’s AC Current and it will burn up a relay not designed for that. If tap into the battery like Dave mention a relay is best as it removes the inefficiency of the control switch. Also use a least a gauge wire down(heavier) from the pigtails on the grip heaters. ...
- Wed May 01, 2019 3:25 pm
- Forum: General Topics
- Topic: McNutt '19
- Replies: 3
- Views: 6550
Re: McNutt '19
Looks awesome.
- Mon Mar 18, 2019 3:27 pm
- Forum: Land Advocacy
- Topic: UCP pitches $30 permit fees for trail users if elected
- Replies: 16
- Views: 24657
Re: UCP pitches $30 permit fees for trail users if elected
I am thinking you mean make existing trails legal to actually create a usable well connected trail network.scubarusteve wrote:Ive got no issues with the fee as long as it keeps riding areas open with potential of new trails
![Thumbs up :thumbsup:](./images/smilies/thumbsup.gif)
- Thu Dec 13, 2018 8:08 am
- Forum: General Topics
- Topic: Neck braces- not a opinion article
- Replies: 4
- Views: 6994
Neck braces- not a opinion article
Hi, thought this was a good read passed along by Cedric. Data seemed quite convincing to me.
https://www.cyclenews.com/2018/12/artic ... ess-study/
https://www.cyclenews.com/2018/12/artic ... ess-study/
- Fri Nov 16, 2018 9:06 pm
- Forum: Technical
- Topic: Suggestions on who to call to remove this screw? Machine Shop?
- Replies: 4
- Views: 5954
Re: Suggestions on who to call to remove this screw? Machine Shop?
Well you haven't destroyed it yet. Could just leave it alone. Set screws are hard steel, they need to be. I think you need to relieve the outer tension on the threads in one of 2 ways. 1. drill a hole close to the inner thread diameter, chances such a small bit will drift and meet the threads. 2. us...